
Metal roof replacement
Metal roof replacement across Sydney, by a roof plumber.
Metal roof replacement across Sydney is what we do: a trade-qualified roof plumber takes the old roof off and lays new steel in its place. Full re-roofs, tile-to-metal conversions, new roofs and the guttering that goes with them.
- Trade
- Our roof plumber holds a Certificate III in Roof Plumbing.
- Work
- We do re-roofs, new roofs and guttering.
- Material
- We work in steel, for roofs and gutters.
- Area
- We cover all of Sydney and get to the west first.
A few of our roofs






What we do
We’re a trade-qualified roof plumber, and we specialise in:

Full re-roof
We take the old roof off and put a new metal one on. While it is open we check the timber underneath and replace anything that has rotted.
Full re-roof →
Tile to metal
Swap a tile roof for steel. The tiles come off, we check the frame is right for the change, and the new roof goes on in sheet.
Tile to metal →
Colorbond
Colorbond steel in the colour and profile (the shape of the sheet) you choose, laid the way the manufacturer says it has to be.
Colorbond →
New roofs
A brand new roof on an extension, a rebuild or a new house. We start at the bare frame and finish the lot.
New roofs →
Guttering
New gutters, downpipes and fascia (the board the gutter is fixed to), either with a new roof or on their own.
Guttering →
Standing seam
A sharper look with no screws showing on the roof. The panels join along a raised seam instead.
Standing seam →
Shed roofs
Sheds, workshops and outbuildings. Usually a one or two day job.
Shed roofs →
Garage roofs
Garages and carports, attached or standalone. Where the garage roof meets the house is the part that has to be right.
Garage roofs →
Commercial
Warehouses, workshops, strata blocks and small industrial units, staged so the building can stay open.
Commercial →Need a roof replacement?
Give us a call or leave your details and we will come out, look at your roof and give you a written quote.
Our process, from start to finish
Three stages, and you will know where we are up to at each one. The price is agreed before any work starts.

1. We measure it
On the roof where we can get to it, off satellite imagery where access is awkward. You get a written quote for your roof.

2. We strip in sections
We plan each day so the section we strip is covered again before we leave.

3. We lay the roof and seal the joins
The sheets go on, then the ridge along the top, the valleys, and the metal strips called flashings that seal around anything coming through the roof. Most leaks start at a flashing, so that is where we take our time.
Don’t leave it too late
Signs your roof needs replacing, not repairing
A metal roof rarely fails across the middle of a sheet. It fails at the edges and the fixings, because that is where water sits and where the metal has been cut. Most of it you can check from a ladder.
- Rust in the valleys
- The valley is where two roof planes meet and every litre of water funnels through it. Rust there means the coating has run out, and it is almost never worth patching on its own.
- Rust rings around the screws
- The washers under the screw heads perish long before the sheet does. Once they have gone, every screw hole is an open path into the roof cavity.
- Water damage on the ceiling that keeps coming back
- A stain that dries out and reappears each winter is an active leak, not old damage. Painting over it hides the stain, but the water is still getting in.
- Damp or daylight in the roof cavity
- Put your head into the manhole with a torch after a wet week. Damp insulation, wet timber or pinpricks of light through the sheet all mean water is getting in across the roof, not just at one spot.
- Ridge capping moving, on a tile roof
- The tiles outlast the mortar that holds down the ridge capping, the row of curved tiles along the top. If the mortar strip has already been redone once (called repointing), the next choice is usually whether to do it again or change to metal.
- Sheets lifting or drumming in wind
- Movement means the screws have lost their grip on the batten, the strip of timber the sheets are screwed to. On an older roof that is the timber failing rather than the screw.
Tile or metal
Many Sydney re-roofs go from tile to metal
A lot of Sydney re-roofs start as tile and go back on in steel. A tile roof needs its mortar redone every ten years or so. A metal roof does not.
| Concrete tile | Metal sheet | |
|---|---|---|
| Weight on the frame | Several tonnes | A fraction of tile |
| Recurring cost | Repointing, every decade or so | No mortar to redo |
| Storm behaviour | Tiles crack and slip individually | Fixed down along its length |
| Condensation | Breathes between tiles | Needs a layer under the sheet, called sarking, to stop condensation |
| Over time | Fades and holds moss | Coated finish, fades slowly |
We’re based in West Hoxton
Servicing all of Sydney, with a focus on the Western suburbs
We replace metal roofs right across Sydney, and the south west and west are closest to us. Tap a suburb on the map, or pick one below, to read about the roofs there.
What it costs
What changes the price of a re-roof
Four things change the price most. The size of the roof is only one of them.
The area, and the shape
Two roofs the same size can cost different amounts. Hips (the sloping edges where two roof faces meet), valleys and dormer windows mean more cutting and more flashing, and that is where the hours go.
What is under the sheet
Rotten battens, the timber strips the sheets are screwed to, get replaced, and nobody knows how many until the old roof is off. Our quote says how they are priced.
Getting on and off it
A single storey with a driveway beside it is a different job to a three storey terrace on a shared wall. Access decides scaffold, and scaffold is real money.
The profile and the coating
The shape of the sheet (corrugated, square-ribbed or standing seam) and the grade of coating you pick both change the sheet price. Standing seam is the dearest and is not always the right answer.
Your roof, your number
Get a real figure for your roof
No job is too small, and we are set up for roofs up to around a thousand square metres. Give us the address and we will come and measure it.
Metal roofers, answered
Questions we get asked a lot
How do I know if my roof needs replacing or just repairing?
Rust in the valleys and rust rings around the fixings usually mean the roof is at the end of its life rather than damaged in one spot. A single leak on an otherwise sound roof is usually a repair rather than a new roof.
Do you replace tile roofs with metal?
Yes. The tiles come off, we check the frame for the lighter load and the battens (the timber strips the roof is fixed to) for the right spacing, and the roof goes back on in steel.
How much does a metal roof replacement cost in Sydney?
It depends on the roof area, the complexity of the shape, access, and how much timber underneath needs replacing. We measure the roof and give you a figure in writing.
Are you a roofer or a plumber?
A roof plumber. In New South Wales roof plumbing covers metal roofs and the gutters, downpipes and flashings (the metal strips that seal the joins) that go with them, so one tradesman can do the whole job.
Which parts of Sydney do you work in?
All of Sydney. We are based in the south west, so we get there fastest. If you are further out, call and ask.
Next step
Find out what your roof will cost
We come out, measure your roof and give you a written quote. The quote says what happens if the timber under the old roof turns out to be worse than it looked. Asking for one does not commit you to anything.


